t qp36918 1 dc- 6 ghz gain block datashe et: rev . e 0 8 / 1 7 /14 - 1 of 8 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com applications ? wireless infrastructure ? catv / satv / moca ? point to point ? defense & aerospace ? test & measurement equipment ? general purpose wireless sot - 363 package product features ? dc ? C ? 6 000 m hz ? flat, broadband frequency response ? 15.3 ? db gain at 1 900? m hz ? 3.6 ? db noise figure at 1 900?m hz ? +29 ? dbm output ip3 at 1 900?m hz ? +14.4 ? dbm p1db at 1 900?m hz ? 50 ohm cascadable gain block ? single supply, 45 ? ma current ? sot - 363 package functional block d iagram pin configuration pin no. label 3 rf in 6 rf out 1, 2, 4, 5 gnd general description the TQP369181 is a general - purpose buffer amplifier that offers high dynamic range in a low - cost surface - mount package. at 1900 mhz , the amplifier typically provides 15.3 ? db gain, +29 ? dbm oip3, and 3.6 ? db noise figure while drawing 45 ? ma current. the device combines dependable performance with consistent quality to maintain mttf values exceeding 100 years at mounting temperatures of +85 ? c. the device is housed in a lead - free/green/rohs - compliant industry - standard sot - 363 package. the TQP369181 consists of a darlington - pair amplifier using the high reliability ingap/gaas hbt process technology. only dc - blocking capacitors, a bias resistor, and an inductive rf choke are r equired for operation. this broadband mmic amplifier can be directly applied to various current and next generation wireless technologies such as cdma, w - cdma, and lte. in addition, the TQP369181 will work for other applications within the dc to 6 ghz frequency range. ordering information part no. description tqp36918 1 ingap/gaas hbt gain block tqp36918 1 - pcb 500? C ?6000?m hz evaluation board standard t/r size = 300 0 pieces on a 7 reel
t qp36918 1 dc- 6 ghz gain block datashe et: rev . e 0 8 / 1 7 /14 - 2 of 8 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com recommended operating conditions parameter min typ max u nits t case ? 40 +85 c tj for >10 6 hours mttf +1 6 0 c electrical specifications are measured at specified test conditions. specifications are not guaranteed over all recommended operating conditions. absolute maximum ratings parameter rating storage temperature ? 55 to 150 ? c rf input power, cw, 50, t=25 c + 27 ? dbm device voltage (v cc ) +5. 2 ? v operation of this device outside the parameter ranges g iven above may cause permanent damage. electrical specifications test conditions unless oth erwise noted: i cc = 45 ? ma, t case = +25 ? c, 50 system parameter conditions min typ max units operational frequency range dc 6 000 mhz test frequency 1900 mhz gain 13. 8 15. 3 16. 8 db input return loss 30 db output return loss 24 db output p1 db +14. 6 dbm output ip3 pout=0 ? dbm/tone, f= 1 ? mhz +26.0 +29. 0 db m noise figure 3.6 db device voltage ? ( v cc ) 3.0 3.9 4.5 v device current ? (i cc ) 45 ma thermal resistance ? ( jc ) junction to c ase ? (1) 226 c/w notes: 1. thermal path is from the d evice junction through the package ground tab (pins 2,4) to the backside mounting surface.
t qp36918 1 dc- 6 ghz gain block datashe et: rev . e 0 8 / 1 7 /14 - 3 of 8 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com s - parameters test conditions: v c c =+3.9 ? v (typ.), i cc =45 ? ma (typ.), t case =+25 ? c, 50 ? system, calibrated to device leads freq ( m hz) s11 (db) s11 (ang) s21 (db ) s21 (ang) s12 (db) s12 (ang) s22 (db) s22 (ang) 10 - 36.7 - 179.3 15.9 179.7 - 18.8 0.3 - 30.2 14.8 20 - 35.9 178.4 15.9 179.3 - 18.8 - 0.1 - 30.0 5.6 50 - 34.6 171.4 15.9 178.5 - 18.8 - 0.3 - 30.8 0.4 100 - 34.1 164.0 15.9 177.2 - 18.8 - 0.7 - 31.2 - 5.2 200 - 32.6 153.3 15.9 174.6 - 18.9 - 0.9 - 30.7 - 10.9 500 - 30.6 137.1 15.8 167.0 - 18.9 - 2.6 - 32.3 - 16.0 900 - 29.1 115.5 15.6 157.3 - 19.0 - 3.8 - 33.1 - 59.1 1000 - 29.1 118.6 15.6 154.9 - 19.0 - 4.1 - 32.0 - 59.5 1500 - 27.9 74.3 15.3 143.1 - 19.1 - 6.1 - 28.2 - 75.7 1900 - 26.7 28.5 15.1 133.6 - 19.4 - 7.5 - 22.9 - 63.3 2000 - 24.9 17.8 15.0 131.3 - 19.4 - 8.0 - 21.7 - 64.4 2500 - 18.2 - 18.4 14.6 120.4 - 19.7 - 9.8 - 16.6 - 62.9 3000 - 14.4 - 24.2 14.2 110.1 - 20.2 - 11.3 - 14.0 - 57.5 3500 - 13.1 - 26.3 13.8 100.4 - 20.5 - 13.1 - 12.9 - 54.0 4000 - 13.1 - 26.2 13.5 91.2 - 20.8 - 12.4 - 13.7 - 50.2 4500 - 15.0 - 20.5 13.3 81.7 - 21.2 - 14.4 - 16.5 - 41.9 5000 - 19.1 0.7 13.1 71.2 - 21.7 - 15.9 - 24.0 0.6 5500 - 20.6 60.7 12.9 60.7 - 22.4 - 17.4 - 18.9 84.1 6000 - 17.1 100.0 12.6 48.8 - 23.2 - 18.4 - 13.5 105.3 notes: 1. m easured on TQP369181- pcb with l1 removed and c2, c3 replaced with 0 resistors. 2. bias applied to device output via internal network analyzer wide - band bias tee. 3. solt ecal at network analyzer test cable ends . 4. input and output reference planes extended to the device leads.
t qp36918 1 dc- 6 ghz gain block datashe et: rev . e 0 8 / 1 7 /14 - 4 of 8 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com tqp36918 1 - pcb evaluation board c2 c1 l1 c3 j4 j3 r1 q1 q1 j2 rf output j4 gnd j3 vcc 3 1,2,4,5 6 j1 rf input l1 39 nh r1 24 ? c3 56 pf c2 56 pf c1 0.018 uf notes: 1. see evaluation board pcb information section for material and stack -up. 2. all components are of 0603 size unless otherwise stated. bill of material ? tqp36918 1 - pcb reference des. value de scription manuf. part number q1 n/a high linearity lna gain block triquint TQP369181 c1 0.018 uf cap, chip, 0603, 16v, x7r, 10% various c2, c3 56 pf cap, chip, 0603, 50v, npo, 5% various l1 39 nh inductor, 0603, 5%, cs series coilcraft 0603cs - 39nxjl r1 res, chip, 0805, 1/10w, 5% various component values for specific frequencies frequency (mhz) 50 500 900 1900 2200 2500 3500 l1 820 nh 220 nh 68 nh 27 nh 22 nh 18 nh 15 nh c2, c3 .018 uf 1000 pf 100 pf 68 pf 68 pf 56 pf 39 pf bias resistor va lues for various supply voltages v supply (v) 5 6 7 8 9 10 12 r1 24 47 68 91 110 130 180 component size 0805 1206 1210 1210 1210 2010 2010
t qp36918 1 dc- 6 ghz gain block datashe et: rev . e 0 8 / 1 7 /14 - 5 of 8 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com typical performance ? tqp36918 1 - pcb test conditions unless otherwise noted: v supply =+5 v, r 1 = 24 , i cc = 45 ma, t case = +25 c parameter typical value units frequency 500 900 1900 2100 2600 3500 4000 5000 6000 mhz gain 15.6 15. 6 15. 3 15.0 14.7 13.8 13.5 13.1 12.6 db input return loss 17 26 30 24 17 13 13 19 17 db output return loss 16 24 2 4 20 16 13 14 24 14 db output p1db +15.4 +15.2 +14.6 +14.3 +14.4 +13.9 +13.0 +12.1 +8.8 dbm oip3 +30.6 +30.0 +29.0 +28.5 +27.7 +26.3 +25.3 +22.0 +22.2 dbm noise f igure 3.6 3.6 3.6 3.6 3.7 4.0 4.0 4.0 4.4 db notes: 1. oip3 measured with two tones at an ou tput power of 0 dbm / tone separated by 1 mhz . performance pl ots ? tqp36918 1 - pcb test conditions unless otherwise noted: v supply =+5 v, r 1 = 24 , i cc = 45 ma, t case = +25 c 6 9 12 15 18 0 1000 2000 3000 4000 5000 6000 gain (db) frequency (mhz) gain vs. freq over temp +85 c +25 c ?40 c - 40 - 30 - 20 - 10 0 0 1000 2000 3000 4000 5000 6000 input return loss (db) frequency (mhz) input return loss vs. freq over temp +85 c +25 c ?40 c - 40 - 30 - 20 - 10 0 0 1000 2000 3000 4000 5000 6000 output return loss (db) frequency (mhz) output return loss vs. freq over temp +85 c +25 c ?40 c 22 24 26 28 30 32 - 3 - 2 - 1 0 1 2 3 oip3 (dbm) output power/tone (dbm) oip3 vs. output power/tone freq.=1900 mhz 1 mhz tone spacing +85 c +25 c ?40 c 12 13 14 15 16 17 18 - 40 - 15 10 35 60 85 p1db (dbm) temperature (deg. c) p1db vs. temperature 900 mhz 1 900 mhz 0 5 10 15 20 25 30 0 1000 2000 3000 4000 5000 6000 p1db (dbm) frequency (mhz) p1db vs. frequency temp.=+25 c temp.=+25 c 10 15 20 25 30 35 40 0 1000 2000 3000 4000 5000 6000 oip3 (dbm) frequency (mhz) oip3 vs. frequency 1 mhz tone spacing pout=0 dbm.per tone temp.=+25 c 0 2 4 6 8 0 1000 2000 3000 4000 5000 6000 nf (db) frequency (mhz) nf vs. frequency temp.=+25 c temp.=+25 c temp.=+25 c
t qp36918 1 dc- 6 ghz gain block datashe et: rev . e 0 8 / 1 7 /14 - 6 of 8 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com pin configuration and description pin no. label description 3 rf in rf i nput, matched to 50 o hms. external dc block is required. 6 rf out rf o utput / dc supply , matched to 50 o hms . external dc bl k bi h k d d i i i i d 1, 2, 4, 5 gnd rf/dc ground. use recommended via pattern to minimize inductance and thermal resistance. see pcb mounting pattern for suggested footprint. evaluation board pcb information triquint pcb 10 82269 material and stack - up 1 oz. cu bottom layer nelco n-4000-13 core nelco n-4000-13 1 oz. cu top layer 1 oz. cu inner layer 1 oz. cu inner layer 0.062" 0.006" finished board thickness 0.014" 0.014" 50 ohm line dimensions: width=0.02 9 " spacing=0.0 35 "
t qp36918 1 dc- 6 ghz gain block datashe et: rev . e 0 8 / 1 7 /14 - 7 of 8 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com package marking and dimensions the top surface of the package is marked with a 181 designator and the bottom surface is marked with an alphanumeric lot code. t op bottom -h- -a- 4 3 5 4 3 .15 c d 2x -d- .30 c both sides (6x) b .10 c a-b d 5 -b- .10 c -c- 6x seating plane .15 c a-b 2x c a2 a1 a symbol a min max top view side view a1 a2 d e e1 l l1 l2 b c - 1.10 (0.043) 0.10 (0.004) 0 1.00 (0.039) 0.70 (0.028) 2.00 (0.079 basic 2.10 (0.083) basic 1.25 (0.049) basic 0.41 (0.016) 0.21 (0.008) 0.42 (0.017) ref 0.15 (0.006) basic 8`8 0`8 12`8 4`8 e 1.30 (0.051) basic c 0.65 (0.026) basic 0.30 (0.012) 0.15 (0.006) 0.08 (0.003) 0.22 (0.009) e1 e1/2 d e1 pin 1 id e/2 e e l2 gauge plane -c- seating plane ? 8x 01 e1 ? ?1 notes: 1. dimensions are in millimeters (inches) 2. dimensions and tolerances per asme y14.5m - 1194. package conforms to jedec mo - 203, issue b. pcb mounting pattern 4.064 [0.160] 2x 0.762 [0.030] 0.381 [0.015] 0.762 [0.030] 2.515 [0.099] 2x 1.207 [0.048] 16x ?.254 (.010) plated thru via holes 1.524 [0.060] 2x 0.773 [0.030] 1.301 [0.051] 2x 1.270 [0.050] 6.329 [0.249] 2x 0.203 [0.01] 2x 0.406 [0.016] 6 2x 0.939 [0.037] 4x 0.889 [0.035] 4x 0.889 [0.035] 2x 0.914 [0.036] 2x 0.387 [0.015] notes: 1. all dimensions are in millimeters(inches). angles are in degrees. 2. use 1 oz. copper minimum for top and bottom layer metal. 3. vias are required under the backside paddle of this device for proper rf/dc grounding and thermal dissipation. 4. do not remove or minimize via hole structure in the pcb. thermal and rf grounding is critica l. 5. we recommend a 0.35mm (#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.10). 6. the rf i/o trace transition shown is to a 30 mil wide line. modify transition as required to interface with other line widths. 1 81
t qp36918 1 dc- 6 ghz gain block datashe et: rev . e 0 8 / 1 7 /14 - 8 of 8 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com product compliance information esd sensitivity ratings caution! esd - sensitive device esd rating: class 1 c value: 1000 v and < 2 000 v test: human body model (hbm) standard: jedec standard js - 001 - 2012 esd rating: cl ass c3 value: 1000 v test: charged device model (cdm) standard: jedec standard jesd22 - c101 f solderability compatible with both lead - free (260 ? c maximum reflow temperature) and tin/lead (245 ? c maximum reflow temperature) soldering processes. con tact plating: nipdau rohs compliance this part is compliant with eu 2002/95/ec rohs directive (restrictions on the use of certain hazardous substances in electrical and electronic equipment). this product also has the following attributes: ? lead free ? halogen free (chlorine, bromine) ? antimony free ? tbbp - a (c 15 h 12 br 4 0 2 ) free ? pfos free ? svhc free msl rating msl rating: level 1 test: 260c convection reflow standard: jedec standard ipc/jedec j - std - 020 contact information for the latest specifica tions, additional product information, worldwide sales and distribution locations, and information about triquint: web: www.triquint.com tel: +1.503.615.9000 email: info - sales@t riquint .com fax: +1.503.615.8902 for technical questions and application information: email: sjcapplications.engineering@ triquint .com important notice the information co ntained herein is believed to be reliable. triquint makes no warranties regarding the information contained herein. triquint assumes no responsibility or liability whatsoever for any of the information contained herein. triquint assumes no responsibilit y or liability whatsoever for the use of the information contained herein. the information contained herein is provided "as is, where is" and with all faults, and the entire risk associated with such information is entirely with the user. all information contained herein is subject to change without notice. customers should obtain and verify the latest relevant information before placing orders for triquint products. the information contained herein or any use of such information does not grant, explici tly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. triquint products are not warranted or authorized for use as critical components in medical, life - saving, or life - sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death.
|
